After this lesson
- Solve a scrambled 3×3 without help
- Understand what each beginner algorithm does
- Recognise and fix the common failure cases
The plan
The beginner method solves the cube in layers. It is slower than CFOP, but it is reliable: every step has a small number of cases and a clear goal. Do not try to memorise all the algorithms at once. Learn one step, practise it on a scrambled cube until it is boring, then move on.
- 1. White cross on the bottom
- 2. White corners — the first layer is complete
- 3. Middle-layer edges — the first two layers are complete
- 4. Yellow cross on top
- 5. Yellow face — orient every last-layer sticker
- 6. Permute the last-layer corners
- 7. Permute the last-layer edges
1. The white cross
Choose white as your bottom colour. Build a cross of four white edges around the white centre, with the side colours matching the adjacent centres. The cross is intuitive: you are not memorising an algorithm, you are moving edges into place.
A useful habit is to do the cross on the bottom. Turning the cube over to inspect the top costs time later. If an edge is stuck in the middle layer, move it into the top layer first, align it, then insert it.
Do not worry about the corners yet. A cross with four correct side stickers is the goal.
2. First-layer corners
Insert the four white corners one at a time. Put the target corner above its slot, then use the same three-move trigger repeatedly until it drops in. The trigger is R U R' U' — the sexy move.
If a corner is in the layer but twisted, take it out with the trigger, reposition it, and insert it again. Do not rotate the whole cube to force a case; keep white on the bottom.
R U R' U'
Repeat until the white corner is solved. If the corner is already in the slot but twisted, apply the trigger to remove it first.
3. Middle-layer edges
Turn the cube so the completed white layer is on the bottom. Find an edge in the top layer that belongs in the middle layer. Align its front colour with the matching centre. Then insert it left or right.
If an edge is in the middle layer but in the wrong slot, insert any other edge into that slot to pop it out, then solve it normally.
U R U' R' U' F' U F
Insert an edge into the right-hand middle slot.
U' L' U L U F U' F'
Insert an edge into the left-hand middle slot.
4. The yellow cross
With two layers complete, look at the top face. You will see a dot, a line, or an L-shaped hook. The same short algorithm fixes all three, but the number of repetitions and the orientation differ.
Line: hold it horizontally across the front and apply F R U R' U' F' once. Hook: hold it in the top-left and apply the same algorithm. Dot: apply it once to reach the line or hook, then continue.
F R U R' U' F'
The yellow-cross algorithm. Re-apply after re-orienting if needed.
5. The yellow face
Now every top edge is oriented, but the corners may not be. You will meet Sune, Anti-Sune and a few other patterns. The beginner method uses one algorithm — Sune — and repeats it with different orientations.
Hold the cube so that exactly one yellow corner is correctly oriented at the front-left, or follow the diagram on the beginner algorithm pages. Repeating Sune cycles the orientation of the corners. Never twist a corner by hand.
R U R' U R U2 R'
Sune. Repeat with the correct orientation until the whole top face is yellow.
If the last layer seems impossible, check that you have not accidentally turned a middle slice or twisted a corner. A single twisted corner is not a reachable state.
6. Permuting the last layer
The top face is yellow, but the corners and edges are probably in the wrong places. First permute the corners, then the edges. The beginner method uses a small set of PLL algorithms: T perm, Y perm, Ua, Ub, H and Z.
Find a side with two matching corner stickers (headlights). Hold it at the back and apply the corner-permutation algorithm. Then use Ua or Ub to cycle the last three edges into place.
R U R' U' R' F R2 U' R' U' R U R' F'
T perm — a corner swap and edge swap used in the beginner finish.
Practise in the right order
Solve the cross ten times. Then solve the cross and corners ten times. Add one layer at a time. If you jump straight to full solves, you will practise recovery more than technique.
Use the 3D studio to replay an algorithm from the exact case. Use the timer only after you can finish a solve without looking anything up — speed comes from repetition, not from rushing a method you do not know yet.
A beginner solve in 2–4 minutes is normal. A first solve in 10 minutes is also normal. The first goal is completion, not the clock.
Check your understanding
1. Which layer does the beginner method solve first?
2. What does the algorithm F R U R' U' F' do?
3. How many yellow corners are correctly oriented in a Sune case?